BPI Open debugger burn board
  • Initial page
  • LANGS
  • BPI Open debugger burn board
    • BPI Open debugger burn board Abbreviations
    • Summary
    • Connection CC Debugger and CC85xx
    • Download the program using the SWD in J-Flash
    • Open Debugger Uart use of STC microcontroller programming interface
    • Operating condition
    • Supported PC Tools
    • Open Debugger CC Debugger module functions in use
    • Use SmartRFProg tools to program the CC series chips
    • SWD Interface：
    • Installing the USB device driver
    • Download SWD debug using the IAR EWARM
    • Use SWD debug download the MDK-ARM
    • CC Debugger Interface：
    • CC-Debugger connection and Transceivers Transceiver
    • MDK-ARM SWD interface in single-step debugging
    • Use Uni flash via JTAG and UART interface to TI CC3200 in the curing process
    • SWD interface IAR EWARM single-step debugging
    • CC- Debugger connected to the SoC device
    • CC Debugger LED light
    • Reference
    • SWD interface device connected to the SOC
    • UART Interface：
    • JTAG/Uart Interface：
    • CC Debugger firmware update
  • BPI Open debugger burn board
    • SWD interface device connected to the SOC
    • Reference
    • UART Interface：
    • JTAG/Uart Interface：
    • Use SmartRFProg tools to program the CC series chips
    • Summary
    • Supported PC Tools
    • Connection CC Debugger and CC85xx
    • Installing the USB device driver
    • Download SWD debug using the IAR EWARM
    • Use SWD debug download the MDK-ARM
    • Download the program using the SWD in J-Flash
    • use-steps
    • Open Debugger Uart use of STC microcontroller programming interface
    • Operating condition
    • All banana pi product
    • Open Debugger CC Debugger module functions in use
    • bpi40customizedserver
    • SWD Interface：
    • connect-the-emulator-and-target-board
    • CC Debugger LED light
    • CC Debugger Interface：
    • support-objects
    • CC-Debugger connection and Transceivers Transceiver
    • MDK-ARM SWD interface in single-step debugging
    • Use Uni flash via JTAG and UART interface to TI CC3200 in the curing process
    • SWD interface IAR EWARM single-step debugging
    • CC Debugger firmware update
    • BPI Open debugger burn board Abbreviations
    • CC- Debugger connected to the SoC device
Powered by GitBook
On this page

Was this helpful?

  1. BPI Open debugger burn board

Use SmartRFProg tools to program the CC series chips

PreviousOpen Debugger CC Debugger module functions in useNextSWD Interface：

Last updated 5 years ago

Was this helpful?

To illustrate, as an example is used here CC2530

1.First open SmartRFProg software, which can be downloaded separately, can also be found in the bin directory under SmartRF Studio installation directory, open the rear as shown below.

2.Then the device is connected to the interface with the CC2530 in CCdebugger Open Debugger on. There need to connect the line VCC, GND, DC, DD, Target, RST which a few lines. After connecting, press the reset button。

3.Under normal circumstances, the state next to the CC Debugger will turn green, if not green, such as red, orange, or other circumstances, please check the wiring is correct, the power supply is normal. If the status is green, then the device list of scanned SmartRFProg equipment will appear as shown below.

4.Then in the next Flash image input box below the list of devices have a button, click to select the firmware file to be programmed, the following Actions select Erase, program and verify, after everything is ready you can click the button below the long long Perfrom action. If the write error, it will output to the progress bar the wrong reasons, and if successful will be similar to the following programming.