How to build OpenWRT image from github

PreviousBPI-M1 SATA interface NextOfficeal OpenWRT

Last updated 5 years ago

Was this helpful?

[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.18.19 (charli@charli-pc) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #3 SMP PREEMPT Mon Aug 24 22:13:58 CST 2015 [ 0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: BPI R1 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 260096 [ 0.000000] free_area_init_node: node 0, pgdat c0503740, node_mem_map ef00a000 [ 0.000000] Normal zone: 1520 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 194560 pages, LIFO batch:31 [ 0.000000] HighMem zone: 512 pages used for memmap [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: Using PSCI v0.1 Function IDs from DT [ 0.000000] PERCPU: Embedded 9 pages/cpu @eefe1000 s6272 r8192 d22400 u36864 [ 0.000000] pcpu-alloc: s6272 r8192 d22400 u36864 alloc=9*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 258576 [ 0.000000] Kernel command line: console=ttyS0,115200 earlyprintk rootwait root=/dev/mmcblk0p2 [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1025388K/1040384K available (3811K kernel code, 169K rwdata, 1068K rodata, 200K init, 606K bss, 14996K reserved, 262144K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc04cbef4 (4880 kB) [ 0.000000] .init : 0xc04cc000 - 0xc04fe000 ( 200 kB) [ 0.000000] .data : 0xc04fe000 - 0xc0528738 ( 170 kB) [ 0.000000] .bss : 0xc0528738 - 0xc05c0048 ( 607 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000009] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns [ 0.000022] Switching to timer-based delay loop, resolution 41ns [ 0.000352] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns [ 0.000510] sched_clock: 32 bits at 160MHz, resolution 6ns, wraps every 26843545593ns [ 0.000673] Console: colour dummy device 80x30 [ 0.000702] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.000718] pid_max: default: 32768 minimum: 301 [ 0.000824] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000837] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001454] CPU: Testing write buffer coherency: ok [ 0.001761] /cpus/cpu@0 missing clock-frequency property [ 0.001778] /cpus/cpu@1 missing clock-frequency property [ 0.001791] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.001847] Setting up static identity map for 0x40011b68 - 0x40011b9c [ 0.060422] CPU1: Booted secondary processor [ 0.060466] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.060535] Brought up 2 CPUs [ 0.060557] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.060564] CPU: All CPU(s) started in HYP mode. [ 0.060569] CPU: Virtualization extensions available. [ 0.064967] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4 [ 0.065370] pinctrl core: initialized pinctrl subsystem [ 0.065762] regulator-dummy: no parameters [ 0.071879] NET: Registered protocol family 16 [ 0.072229] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.111482] reg-fixed-voltage ahci-5v: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/ahci_pwr_pin@0, deferring probe [ 0.111521] platform ahci-5v: Driver reg-fixed-voltage requests probe deferral [ 0.111550] reg-fixed-voltage usb1-vbus: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe [ 0.111565] platform usb1-vbus: Driver reg-fixed-voltage requests probe deferral [ 0.111589] reg-fixed-voltage usb2-vbus: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb2_vbus_pin@0, deferring probe [ 0.111603] platform usb2-vbus: Driver reg-fixed-voltage requests probe deferral [ 0.111817] vcc3v0: 3000 mV [ 0.112040] vcc3v3: 3300 mV [ 0.112264] vcc5v0: 5000 mV [ 0.112345] reg-fixed-voltage gmac-3v3: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/gmac_power_pin@0, deferring probe [ 0.112362] platform gmac-3v3: Driver reg-fixed-voltage requests probe deferral [ 0.112811] SCSI subsystem initialized [ 0.112885] libata version 3.00 loaded. [ 0.113197] usbcore: registered new interface driver usbfs [ 0.113274] usbcore: registered new interface driver hub [ 0.113403] usbcore: registered new device driver usb [ 0.113546] pps_core: LinuxPPS API ver. 1 registered [ 0.113553] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.113584] PTP clock support registered [ 0.114654] Switched to clocksource arch_sys_counter [ 0.121779] NET: Registered protocol family 2 [ 0.122818] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.122902] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.123024] TCP: Hash tables configured (established 8192 bind 8192) [ 0.123105] TCP: reno registered [ 0.123122] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.123179] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.123443] NET: Registered protocol family 1 [ 0.124957] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.125108] audit: initializing netlink subsys (disabled) [ 0.125185] audit: type=2000 audit(0.110:1): initialized [ 0.133939] VFS: Disk quotas dquot_6.5.2 [ 0.134207] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.135970] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.135994] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.136719] msgmni has been set to 1490 [ 0.138903] bounce: pool size: 64 pages [ 0.138931] io scheduler noop registered [ 0.138946] io scheduler deadline registered [ 0.138996] io scheduler cfq registered (default) [ 0.139318] platform 1c13400.phy: Driver sun4i-usb-phy requests probe deferral [ 0.142025] sun7i-a20-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 0.184985] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 0.187319] console [ttyS0] disabled [ 0.207743] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 33, base_baud = 1500000) is a U6_16550A [ 0.828354] console [ttyS0] enabled [ 0.854828] 1c28c00.serial: ttyS1 at MMIO 0x1c28c00 (irq = 36, base_baud = 1500000) is a U6_16550A [ 0.886744] 1c29c00.serial: ttyS2 at MMIO 0x1c29c00 (irq = 52, base_baud = 1500000) is a U6_16550A [ 0.899279] platform 1c50000.ethernet: Driver stmmaceth requests probe deferral [ 0.906754] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.913282] ehci-platform: EHCI generic platform driver [ 0.918683] platform 1c14000.usb: Driver ehci-platform requests probe deferral [ 0.926000] platform 1c1c000.usb: Driver ehci-platform requests probe deferral [ 0.933320] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.939546] ohci-platform: OHCI generic platform driver [ 0.944901] platform 1c14400.usb: Driver ohci-platform requests probe deferral [ 0.952185] platform 1c1c400.usb: Driver ohci-platform requests probe deferral [ 0.959587] usbcore: registered new interface driver usb-storage [ 0.965867] mousedev: PS/2 mouse device common for all mice [ 0.971551] 1c22800.lradc supply vref not found, using dummy regulator [ 0.978474] input: 1c22800.lradc as /devices/soc@01c00000/1c22800.lradc/input/input0 [ 0.991771] axp20x-regulator axp20x-regulator: regulators node not found [ 0.998630] LDO1: 1300 mV [ 1.001767] LDO2: at 3000 mV [ 1.005157] LDO3: at 2275 mV [ 1.008294] LDO4: at 2800 mV [ 1.011695] LDO5: at 2800 mV [ 1.015085] DCDC2: at 1400 mV [ 1.018533] DCDC3: at 1250 mV [ 1.021668] axp20x 0-0034: AXP20X driver loaded [ 1.027508] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 1.036066] sunxi-mmc 1c0f000.mmc: No vqmmc regulator found [ 1.041994] sunxi-mmc 1c0f000.mmc: Got CD GPIO [ 1.084877] sunxi-mmc 1c0f000.mmc: base:0xf00fa000 irq:64 [ 1.092685] sunxi-ss 1c15000.crypto-engine: Die ID 0 [ 1.099853] TCP: cubic registered [ 1.103201] Initializing XFRM netlink socket [ 1.107611] NET: Registered protocol family 17 [ 1.112178] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 1.124806] 8021q: 802.1Q VLAN Support v1.8 [ 1.129125] Registering SWP/SWPB emulation handler [ 1.134455] registered taskstats version 1 [ 1.139223] ahci-5v: 5000 mV [ 1.142597] usb1-vbus: 5000 mV [ 1.147273] usb2-vbus: 5000 mV [ 1.150752] gmac-3v3: 3300 mV [ 1.192892] mmc0: host does not support reading read-only switch, assuming write-enable [ 1.203577] mmc0: new high speed SDHC card at address 0001 [ 1.209591] mmcblk0: mmc0:0001 00000 7.44 GiB [ 1.215221] mmcblk0: p1 p2 [ 1.264746] stmmaceth 1c50000.ethernet: no reset control found [ 1.270578] Ring mode enabled [ 1.273630] No HW DMA feature register supported [ 1.278179] Normal descriptors [ 1.281500] TX Checksum insertion supported [ 1.292504] libphy: stmmac: probed [ 1.295950] eth0: PHY ID 03625f24 at 0 IRQ POLL (stmmac-0:00) active [ 1.302298] eth0: PHY ID 03625f24 at 1 IRQ POLL (stmmac-0:01) [ 1.308050] eth0: PHY ID 03625f24 at 2 IRQ POLL (stmmac-0:02) [ 1.313789] eth0: PHY ID 03625f24 at 3 IRQ POLL (stmmac-0:03) [ 1.319538] eth0: PHY ID 03625f24 at 4 IRQ POLL (stmmac-0:04) [ 1.325287] eth0: PHY ID 03625f24 at 30 IRQ POLL (stmmac-0:1e) [ 1.331456] ehci-platform 1c14000.usb: EHCI Host Controller [ 1.337154] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 1.345031] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000 [ 1.364665] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 1.370952] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.377753] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.384988] usb usb1: Product: EHCI Host Controller [ 1.389862] usb usb1: Manufacturer: Linux 3.18.19 ehci_hcd [ 1.395353] usb usb1: SerialNumber: 1c14000.usb [ 1.400464] hub 1-0:1.0: USB hub found [ 1.404250] hub 1-0:1.0: 1 port detected [ 1.408963] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.414564] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 1.422482] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000 [ 1.444681] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 1.450961] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.457766] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.464991] usb usb2: Product: EHCI Host Controller [ 1.469865] usb usb2: Manufacturer: Linux 3.18.19 ehci_hcd [ 1.475355] usb usb2: SerialNumber: 1c1c000.usb [ 1.480460] hub 2-0:1.0: USB hub found [ 1.484246] hub 2-0:1.0: 1 port detected [ 1.488775] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 1.495451] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 [ 1.503327] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400 [ 1.568861] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.575669] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.582883] usb usb3: Product: Generic Platform OHCI controller [ 1.588814] usb usb3: Manufacturer: Linux 3.18.19 ohci_hcd [ 1.594296] usb usb3: SerialNumber: 1c14400.usb [ 1.599360] hub 3-0:1.0: USB hub found [ 1.603146] hub 3-0:1.0: 1 port detected [ 1.607711] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 1.614350] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 [ 1.622242] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400 [ 1.688838] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.695643] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.702858] usb usb4: Product: Generic Platform OHCI controller [ 1.708790] usb usb4: Manufacturer: Linux 3.18.19 ohci_hcd [ 1.714271] usb usb4: SerialNumber: 1c1c400.usb [ 1.719358] hub 4-0:1.0: USB hub found [ 1.723148] hub 4-0:1.0: 1 port detected [ 1.732286] ahci-5v: disabling [ 1.735459] vcc5v0: disabling [ 1.738427] vcc3v0: disabling [ 1.743698] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities [ 1.752677] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities [ 1.766260] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Opts: (null) [ 1.773791] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 1.780839] Freeing unused kernel memory: 200K (c04cc000 - c04fe000) [ 1.804732] usb 2-1: new high-speed USB device number 2 using ehci-platform [ 1.896387] init: Console is alive [ 1.900086] init: - watchdog - [ 1.956437] usb 2-1: New USB device found, idVendor=0bda, idProduct=8178 [ 1.963264] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 1.970476] usb 2-1: Product: 802.11n WLAN Adapter [ 1.975289] usb 2-1: Manufacturer: Realtek [ 1.979482] usb 2-1: SerialNumber: 00e04c000001 [ 2.114708] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP [ 2.122202] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1 [ 2.128109] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 2.137085] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 2.146090] scsi host0: ahci_platform [ 2.150140] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 [ 2.504668] ata1: SATA link down (SStatus 0 SControl 300) [ 2.903980] init: - preinit - [ 3.049304] b53_common: found switch: BCM53125, rev 4 [ 3.064921] RX IPC Checksum Offload disabled [ 3.069283] No MAC Management Counters available [ 4.240130] random: mktemp urandom read with 5 bits of entropy available [ 5.044697] stmmaceth 1c50000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 7.303617] mount_root: mounting /dev/root [ 7.313783] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [ 7.324800] procd: - early - [ 7.327825] procd: - watchdog - [ 8.196631] procd: - ubus - [ 9.200629] procd: - init - [ 9.740779] NET: Registered protocol family 10 [ 9.750621] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 9.781222] Loading modules backported from Linux version master-2015-03-09-0-g141f155 [ 9.789242] Backport generated by backports.git backports-20150129-0-gdd4a670 [ 9.797957] ip_tables: (C) 2000-2006 Netfilter Core Team [ 9.808055] nf_conntrack version 0.5.0 (16024 buckets, 64096 max) [ 9.895305] xt_time: kernel timezone is -0000 [ 9.909554] cfg80211: Calling CRDA to update world regulatory domain [ 9.916314] cfg80211: World regulatory domain updated: [ 9.921471] cfg80211: DFS Master region: unset [ 9.926943] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 9.936834] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 9.944963] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 9.952992] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 9.961171] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 9.969328] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 9.978922] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 9.987125] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 9.995867] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 10.033695] PPP generic driver version 2.4.2 [ 10.039216] NET: Registered protocol family 24 [ 10.057795] rtl8192cu: Chip version 0x11 [ 10.148074] rtl8192cu: MAC address: ac:a2:13:5c:96:bf [ 10.153232] rtl8192cu: Board Type 0 [ 10.164227] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1 [ 10.170284] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw_TMSC.bin [ 10.177753] ieee80211 phy0: Selected rate control algorithm 'rtl_rc' [ 10.179863] usbcore: registered new interface driver rtl8192cu [ 11.862773] random: nonblocking pool is initialized [ 14.869421] b53_common: found switch: BCM53125, rev 4 [ 14.899568] RX IPC Checksum Offload disabled [ 14.916057] No MAC Management Counters available [ 14.921020] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.864711] stmmaceth 1c50000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 16.872809] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 220.810635] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 221.264426] rtl8192cu: MAC auto ON okay! [ 221.301871] rtl8192cu: Tx queue select: 0x05 [ 221.725855] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 221.734477] device wlan0 entered promiscuous mode [ 221.739510] br-lan: port 1(wlan0) entered forwarding state [ 221.745096] br-lan: port 1(wlan0) entered forwarding state [ 221.752455] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 221.772506] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 223.741765] br-lan: port 1(wlan0) entered forwarding state