Lamobo Openwrt 镜像

用于BPI-R1的opnewrt系统由LAMOBO提供支持。

此分支基于Openwrt 主分支 r42830构建。

Q&A

  • 我是bpi新用户，那么我该怎么使用这个固件呢？ 1. For a new user, we recommend to use the ready configured firmware. please download it from forum download page: http://elastos.org/elorg_common/Lamobo-R1/2015-01-12/openwrt-sunxi-Lamobo-R1-sdcard-vfat-ext4.img 2. BPI-R1支持TF卡 ，请确保您的TF卡空间大于512MB。使用以下命令生成可以引导的TF卡： $ sudo dd if=openwrt-sunxi-BPI-R1-sdcard-vfat-ext4-configured.img of=/dev/sdX bs=1MB

  • 关于固件的注意事项：

  • 如果我使用了原始固件，我改怎么办？

    1. The original firmware is built directly from source code. It almost does not install software, except OpenWrt base software. Please download it from:elastos.org/elorg_common/Lamobo-R1/2015-...sdcard-vfat-ext4.img.

    2. Prepare a TTL thread for to connent OpenWrt bash terminal.

    3. Connect to OpenWrt terminal throught TTL thread, modify OpenWrt packages source. All Of OpenWrt packages is released on: elastos.org/elorg_common/Lamobo-R1/2014-01-12/packages. You can change opkg.conf(/etc/opkgopkg.conf) content to below: src/gz chaos_calmer_base http://elastos.org/elorg_common/Lamobo-R1/2014-01-12/packages/base src/gz chaos_calmer_luci http://elastos.org/elorg_common/Lamobo-R1/2014-01-12/packages/luci src/gz chaos_calmer_management http://elastos.org/elorg_common/Lamobo-R1/2014-01-12/packages/management src/gz chaos_calmer_packages http://elastos.org/elorg_common/Lamobo-R1/2014-01-12/packages/packages src/gz chaos_calmer_routing http://elastos.org/elorg_common/Lamobo-R1/2014-01-12/packages/routing src/gz chaos_calmer_telephony http://elastos.org/elorg_common/Lamobo-R1/2014-01-12/packages/telephony And then, update opkg database: $ opkg update

    4. Install OpenWrt packages. The below packages are needed:

      $ opkg install kmod-b53
$ opkg install kmod-rtl*
$ opkg install hostapd
$ opkg install wpa-supplicant
$ opkg install luci-proto-ppp
$ opkg install ppp-mod-pptp
$ opkg install luci
$ opkg install luci-theme-bootstrap

      Full package list please refer: kingone.elastos.org/2015/01/13/lamobo-r1-package-list/

    5. Modify the network config.Append below text to “/etc/config/network”:

      config switch ‘eth0′ option enable ’1′ option enable_vlan ’1′ option reset ’1′

      config interface ‘lan’ option proto ‘static’ option ipaddr ’10.0.1.1′ option netmask ’255.255.255.0′ option defaultroute ’0′ option peerdns ’0′ option nat ’1′ option ifname ‘eth0.1′ option type ‘bridge’

      config switch_vlan option device ‘eth0′ option ports ’0 1 2 4 8t’ option vlan ’1′

      config interface ‘wan’ option ifname ‘eth0.2′ option proto ‘dhcp’

      config switch_vlan option device ‘eth0′ option vlan ’2′ option ports ’3 8t’```

      start router web server:

$ /etc/init.d/uhttpd start $ /etc/init.d/uhttpd enable```

That’s all. Good luck!

forum discuss link:

http://www.bananapi.com/index.php/forum/general/417-banana-pi-bpi-r1-openwrt-image-2-0-release-note#1229

Wiki link:

http://wiki.geiges.net/doku.php?id=openwrt_bpi-r1

PreviousNas for BPINextLamobo Openwrt image

Last updated