banana pi BPI-G1 open source IoT development board
  • Initial page
  • LANGS
  • About BPI-G1 IoT development board
    • BPI-G1 hardware
    • Summary
    • BPI-G1 Other Accessories
    • Which IDE development can use
    • Quick start of TI CC2530
    • Quick Start STM32F103CB
    • BPI-G1 Simple Code Firmware programming manual
    • Quick start of TI CC3200
    • BPI-G1 smart home gateway project
    • Which emulator debugging
    • BPI-G1 Global Power and Ground
    • BPI-G1 Hardware Specifications
    • Some of the features TI CC2540/1
    • Status LEDs for each module
    • BPI-G1 Main features
    • BPI-G1 Quick Start
    • Explanation
    • Some of the features TI CC2530
    • Some of the features TI CC3200
    • Some of the features STM32F103CB
    • TI CC3200 part Peripheral Interface
    • TI CC2530 part Peripheral Interface
    • Button
    • STM32F103CB part Peripheral Interface
    • CC2530 connection with F103
    • CC2540 connection with F103
    • BPI Open debugger burn board
    • TI CC3200 mode selection jumper
    • TI CC2540/1 part Peripheral Interface
    • BPI-G1 Module interconnection
    • BPI-G1 hardware interface
    • BPI-G1 Accessories
    • Quick start of TI CC2540/1
  • About BPI-G1 IoT development board
    • BPI-G1 Global Power and Ground
    • BPI-G1 Schematic
    • Summary
    • BPI-G1 Other Accessories
    • Quick Start STM32F103CB
    • BPI-G1 smart home gateway project
    • CC2530 connection with F103
    • Button
    • BPI Open debugger burn board
    • BPI-G1 Hardware Specifications
    • CC2540 connection with F103
    • All banana pi product
    • bpi40customizedserver
    • BPI-G1 Main features
    • BPI-G1 Quick Start
    • Explanation
    • BPI-G1 hardware interface
    • BPI-G1 Accessories
    • Quick start of TI CC2540/1
    • BPI-G1 hardware
    • BPI-G1 Module interconnection
    • Quick start of TI CC2530
    • Quick start of TI CC3200
    • BPI-G1 Simple Code Firmware programming manual
Powered by GitBook
On this page

Was this helpful?

  1. About BPI-G1 IoT development board

Quick start of TI CC2540/1

PreviousBPI-G1 AccessoriesNextAbout BPI-G1 IoT development board

Last updated 5 years ago

Was this helpful?

The following operations are by CC2540 prevail, if G1 above your hands BLE chip CC2541, so in some way, your own modifications by CC2541.

Download and install the software

Download and install the following software：

  • （Recommends using version 1.3.2, can go to google search to） ault installation folder C:\Texas Instruments\BLE-CC254x-1.3.2

  • IAR EW8051（Please install the software on their own, we recommend using IAR EW8051 8.1).

G1 connection BPI open debugger burn board

BPI open debugger check whether the software and hardware are connected.

If the drive is normal, then check the G1 and OPENDEBBUG connection is normal. After the G1 to power, press the CC Debugger interface Open debugger next reset button.

If the connection is normal, then the status light next to the CC Debugger interface will turn green, if it is red or other colors, please check whether it is normal or electricity on the G1 G1 is properly connected and Open debugger.

Compile, download and debug routines SimpleBLEPeripheral

  1. IAR EW8051 SimpleBLEPeripheral start and open the project, select File> Open from the menu> Workspace.

  2. Browse to C:\Texas Instruments\BLE-CC254x-1.3.2\Projects\ble\SimpleBLEPeripheral CC2540DB and open SimpleBLEPeripheral.eww.

  3. Choose from the list of items CC2540.

  4. When debugging code must be downloaded to the device. Select Project> Options from the menu and select Debugger category. In this setup tab, select Texas Instruments as a driver, and then click OK. Figure.

  5. Click on the icon to download the program debug button on the device and enter debug mode. Figure.

  6. Click Debug Step Out button on the column, enter the full speed.

  7. Then open the phone BLE software, IOS (IPhone4s and above) on the LightBlue, Android (Android4.3 and above) on the Ex039BLE, refresh the list of Bluetooth, you will see a file called SimpleBLEPeripheral of Bluetooth peripherals. Figure.

BPI open debugger connected to the PC, and check whether the drive is installed, if you can not identify, install , he software that comes with the driver. If you can identify that, please give G1 on electricity.

SmartRF Studio
BLE Stack