banana pi BPI-G1 open source IoT development board
  • Initial page
  • LANGS
  • About BPI-G1 IoT development board
    • BPI-G1 hardware
    • Summary
    • BPI-G1 Other Accessories
    • Which IDE development can use
    • Quick start of TI CC2530
    • Quick Start STM32F103CB
    • BPI-G1 Simple Code Firmware programming manual
    • Quick start of TI CC3200
    • BPI-G1 smart home gateway project
    • Which emulator debugging
    • BPI-G1 Global Power and Ground
    • BPI-G1 Hardware Specifications
    • Some of the features TI CC2540/1
    • Status LEDs for each module
    • BPI-G1 Main features
    • BPI-G1 Quick Start
    • Explanation
    • Some of the features TI CC2530
    • Some of the features TI CC3200
    • Some of the features STM32F103CB
    • TI CC3200 part Peripheral Interface
    • TI CC2530 part Peripheral Interface
    • Button
    • STM32F103CB part Peripheral Interface
    • CC2530 connection with F103
    • CC2540 connection with F103
    • BPI Open debugger burn board
    • TI CC3200 mode selection jumper
    • TI CC2540/1 part Peripheral Interface
    • BPI-G1 Module interconnection
    • BPI-G1 hardware interface
    • BPI-G1 Accessories
    • Quick start of TI CC2540/1
  • About BPI-G1 IoT development board
    • BPI-G1 Global Power and Ground
    • BPI-G1 Schematic
    • Summary
    • BPI-G1 Other Accessories
    • Quick Start STM32F103CB
    • BPI-G1 smart home gateway project
    • CC2530 connection with F103
    • Button
    • BPI Open debugger burn board
    • BPI-G1 Hardware Specifications
    • CC2540 connection with F103
    • All banana pi product
    • bpi40customizedserver
    • BPI-G1 Main features
    • BPI-G1 Quick Start
    • Explanation
    • BPI-G1 hardware interface
    • BPI-G1 Accessories
    • Quick start of TI CC2540/1
    • BPI-G1 hardware
    • BPI-G1 Module interconnection
    • Quick start of TI CC2530
    • Quick start of TI CC3200
    • BPI-G1 Simple Code Firmware programming manual
Powered by GitBook
On this page

Was this helpful?

  1. About BPI-G1 IoT development board

Quick Start STM32F103CB

PreviousQuick start of TI CC2530NextBPI-G1 Simple Code Firmware programming manual

Last updated 5 years ago

Was this helpful?

Download and install the following software:

  • IAR EWARM (the software with the IDE compiler CC3200 is the same, if already installed, then the direct use, otherwise the installation yourself, we recommend using IAR EWARM 7.2 or later)

  • Go download SimpleLed

G1 connection BPI open debugger board

BPI open debugger check whether the software and hardware are connected

Compile, download and debug routines SimpleLed

  1. Start IAR EWARM and open SimpleLed project, select File> Open from the menu> Workspace

  2. Browse to bpi_g1_stm32_simpleled SimpleLed and open SimpleLed.eww

  3. Click on the icon to download the program debug button on the device and enter debug mode. Figure

  4. Click Debug Step Out button on the column, enter the full speed

  5. If there is no problem, STM32 lower left corner of the LED will begin to flash lights

BPI Open debugger connected to the PC, and check whether the drive is installed, if you can not identify, install ,which comes with software drivers. If you can identify that, please give G1 powered.

JLinkARM
https://github.com/mark-legend/bpi_g1_stm32_simpleled